Tuesday, October 9, 2018

***Acura ZDX V6-3.7L Technical Service Bulletin # 10-008 Date: 111129


***Acura ZDX V6-3.7L Technical Service Bulletin # 10-008 Date: 111129



Locks - Master Key Won't Lock In Extended Position



10-008



November 29, 2011



Applies To:



See VEHICLES AFFECTED



Retractable Master Key Does Not Lock in Its Extended Position



(Supersedes 10-008, dated April 26, 2010, to revise the information marked by the asterisks)



*REVISION SUMMARY



Under VEHICLES AFFECTED and PARTS INFORMATION, 2011-12 models were added.*



SYMPTOM



The retractable master key does not lock in its extended position.



PROBABLE CAUSE



The release button and the collar on the master key become worn after rough use.



VEHICLES AFFECTED



*2007-12 MDX - ALL*



*2007-12 RDX - ALL*



2007-08 TL - ALL



*2009-12 TL (without push button start)



2009-12 TSX Sedan - ALL



2010-12 ZDX (without push button start)*



CORRECTIVE ACTION



132



Replace the key case, cut the new key to match the original, then rewrite the transponder code into the immobilizer control unit with the HDS



PARTS INFORMATION



Key Case (does not include transmitter or cover):



2007-09 MDX Driver 1



P/N 35121-STX-305



2007-09 MDX Driver 2



P/N 35121-STX-306



*2010-12 MDX Driver 1



P/N 35120-STX-305



2010-12 MDX Driver2



P/N 35120-STX-306*



2007 RDX



P/N 35120-STK-305



*2008-12 RDX Driver 1



P/N 35121-STX-305



2008-12 RDX Driver 2



P/N 35121-STX-306*



2007-08 TL Driver 1



P/N 35120-SEP-305



2007-08 TL- Driver 2



P/N 35120-SEP=306



*2009-12 TL (without push button start) Driver 1



P/N 35120-TK4-305



2009-12 TL (without push button start) Driver 2



P/N 35120-TK4-306



2009-12 TSX Sedan Driver 1



P/N 35120-TL0-307



2009-12 TSX Sedan Driver 2



P/N 35120-TL0-308



2010-12 ZDX (without push button start) Driver 1



P/N 35120-TK4-305



2010-12 ZDX (without push button start) - Driver 2



P/N 35120-TK4-306*



WARRANTY CLAIM INFORMATION



The normal warranty applies.



Operation Number: 1161D3 (one or more keyless



remote modules)



Flat Rate Time: 0.4 hour



Failed Part: P/N 72147-S0K-A23



Defect Code: 03217



Symptom Code: 08201



Skill Level: Repair Technician



REPAIR PROCEDURE



133



NOTE:



Make sure to use a # 0 Phillips Screwdriver that is in good condition, and apply enough down force when removing the screw to avoid damaging



the screw.



1 Using a # 0 Phillips screwdriver, remove the screw from the key case. Remove the cover and the key transmitter.



2. Follow the Decode and Copy instructions on the Matrix X key cutter to cut a new key with the new key case. This allows you to use the original



key without needing the key code.



3. Assemble the cover and the transmitter onto the new key case, and install the screw.



4. To add a key with the HDS, you need these items:



^ The new master key



^ First password (This five character code is available on the iN.) Go to SERVICE, select Vehicle Information from the left column, then



select Immobilizer Code Inquiry.



HDS with software 2.020.018 or later.



NOTE:



Make sure the market, the date, and the time on the HDS setup screen are correct. Select the F12 key in the upper right corner to get the



Set-up Details screen. Make sure Market is set to USA. Select the time display in the lower right corner to get the Date/Time Properties



pop-up window. Make sure the date and time are correct. For details, refer to the HDS Set-up Instructions listed under Tool Information in



ISIS.



5. Connect the HDS to the DLC (data link connector).



6. Insert the client's original key (now without the keyless transmitter) into the ignition switch, and turn the switch to ON (II). Turn on the HDS.



7. At the screen prompts, enter the VIN and the odometer reading, then verify the correct date and time.



8. From the system Selection screen, select IMMOBI.



9. From the Immobilizer Test Mode screen, select Immobilizer Setup.



10. From the Immobilizer Setup screen, select Add and Delete Keys.



134



11. From the Add and Delete Keys screen, select Add 1 Key.



12. From the Add 1 Key screen, select Begin to Add 1 Key.



NOTE:



If there are six keys already in memory, you'll need to stop and do Delete or Add Multiple Keys, but that requires all of the client's keys.



Any key not present will no longer start the engine.



13. From the first password screen, enter the first password, then follow the screen prompts. When you are finished, turn the ignition switch to



LOCK (0), then turn off and disconnect the HDS.