Sunday, October 29, 2017

Mercedes Benz C 63 AMG Technical Service Bulletin #LI27-50_P-0497102 Date: 120703 A/T - Switches To Limp Home Mode And One Or More DTC's Stored Automatic transmission limp-home mode, fault codes 0717, 0718, 0722, 0723, 2200, 2201, 2204, 2205, 2206, 2207, 2767, 2768

Mercedes Benz C 63 AMG Technical Service Bulletin #LI27-50_P-0497102
Date: 120703
A/T - Switches To Limp Home Mode And One Or More DTC's Stored
Automatic transmission limp-home mode, fault codes 0717, 0718,
0722, 0723, 2200, 2201, 2204, 2205, 2206, 2207, 2767, 2768
Numero de tema: L127 5rnF-049710
Version: 2
Grupo de construccion: 27.50 Gear assembly
Edicion: 0703-2012
Validez: Automatic transmission 722.9 it is not possible to repair the EHS (VGS) in AMG vehicles
Motivo de modificacion: Note added: It is not possible to repair the EHS (VCS) in AMG vehicles
Reclamacion:
Automatic transmission 722.9 switches to limp-home while driving (gearshifts no longer possible) and/or one or more of the following fault codes
are stored or current:
For vehicles with VGS1
2200 2201 2204 2205 2206 2207
For vehicles with VGS2 or VGS3
0717, 0718, 0722, 0723, 2767, 27682010 Mercedes Benz C 63 AMG Sedan (204.077) V8-6.3L (156.985)
 
 
Page 28
Causa:
Rpm sensor fault
Remedio:
Process the speed sensor fault codes completely using the DAS/Xentry guided test (possible as of DVD 01/2011 and add-on 1740). This may or may
not entail a replacement of the EHS.
In the case of hardware replacement (when SDS instructs to do so, see attachment) the adaptation data of the old transmission control unit is read out
in the DAS/Xentry guided test and transferred to the new control unit after the repair. Subsequently, the transmission control unit, which is bolted
onto the electrohydraulic controller unit (EHS), may only be replaced using the EHS repair kit (A000 270 17 00) In other cases SDS will provide
alternate instructions
See also the Akubis direct film: "Replacement of "fully integrated transmission control" (VGS) controller unit at electrohydraulic controller unit
(EHS) on automatic transmission 722.9"
The VGS Control Unit (Control Module) only is to be replaced for VGS2 and VGS3 Control Unit versions with these fault codes, when SDS
instructs to do so VGS Control Unit is available as EHS Repair Kit (A000 270 17 00) Complete valve body "Electrohydraulic Controller Unit
(EHS)" replacement is necessary for VCS1 Control Unit versions when SDS instructs to do so. Control Unit Version is identified from the
Transmission Control Unit Log.
Note in Cases where hardware replacement is specified:
This procedure differs from a complete valve body replacement as the adaptation data, coding and valve body calibration data are transferred from
the old VGS Control Unit to the new VGS control unit This data from the old VGS Control Unit is stored in the Star Diagnosis unit by processing
one of the above codes. The same Star Diagnosis SW stem unit MUST be used to process the fault code and perform initial startup of the new VGS
Control Unit. Failure to do so will result in the necessary data not being transferred and improper transmission functionality after VCS Control Unit
replacement.2010 Mercedes Benz C 63 AMG Sedan (204.077) V8-6.3L (156.985)
 
 
Page 29
1. Process the speed sensor fault code completely by following the instructions in DAS/Xentry related to the fault code Note: During the
replacement of the VGS Control Unit it is imperative that the position of the solenoid valves are noted and re-installed in their original positions
Failure to do so will cause a mismatch in the calibration data to respective solenoid valve(s) and subsequent shifting complaints.
2. Replace the VGS Control Unit per WIS instructions For the initial road test following VGS Control Unit replacement the vehicle must be driven
gently for the first several shifts in each gear since it will be necessary to bleed the air from the valve body. Until the air is bleed out irregular
shifting will be noticed momentarily and will clear up with subsequent shift processes. Because the adaptation data is transferred from the
original VGS Control Unit performing subsequent shift adaptations is not necessary.
Note:
It is not possible to repair the EHS (VGS) in AMG vehicles Technical
Service Bulletin # S-54_10-255
Date: 120703
Battery - Battery Charging Information
Date: July 3, 2012
Order No.: S-B-54. 10/255
Group: 54
SUBJECT:
MY-All, All Models Charge Battery
Correct charging of the on-board electrical system battery, starter battery, and buffer battery helps to ensure that the vehicle continues to start,
functions properly, and has optimal battery life. Therefore please remember that all batteries >/= 12 Ah must be charged in the way described in
AR54.10-P-1130CW.
The battery charging period depends on the charge level of the battery.
The battery must be charged using an approved charger (see SSEP catalogue located under "MB Equipment" menu of STAR TekInfo).
The battery is sufficiently charged when the charging current reading is < 25 A. Technical
A/C - Howl, Rattle Noise From Engine Compartment
Howling, rattling noise from engine compartment
Topic number L183.55-P-053465
Version 2
Design Group 83.55 A/C compressor
Date 06-15-2012
Validity Model series 204 and 207 with Valeo refrigerant compressor
Reason for change Model Validity Changed
Complaint:
1. Howling noise from engine compartment.
2. Rattling noise from engine compartment.
Attachments
Cause:
1.
Wear of rubber damper on Valeo refrigerant compressor.
Service Bulletin # LI83-55_P-0534652 Date:
1206152010 Mercedes Benz C 63 AMG Sedan (204.077) V8-6.3L (156.985)
2.
 
 
Page 30
Wear of bearing of belt pulley on refrigerant compressor.
Remedy:
Replacement of belt pulley on refrigerant compressor, see WIS document AR 83.55-P-7685C.
Pay attention to the correct type of refrigerant compressor (Valeo, see picture) and the associated belt pulley diameter (110 mm or 120 mm).
Symptoms
Parts
Work units
Attachment
Defect free rubber damper/Valeo refrigerant compressor2010 Mercedes Benz C 63 AMG Sedan (204.077) V8-6.3L (156.985)
 
 
Page 31
Torn rubber damper